Gadong Taohy

DELL PP39L SPECS PDF

Dell Studio (PP39L) Number of battery cells, 6. Energy reserve, 56 W*h. Dimensions and weight. Width, mm. Length, mm. Thickness, 39 mm. View full Dell Studio 15 specs on CNET. Dell Studio 15 Laptop Computer (Intel Unknown/NA T, GB HDD, 2GB RAM). Part Number: DNDWUW1. View full Dell Studio SB specs on CNET. Notebook type. Thin-and- light ( lbs.) Screen type. Widescreen. Manufacturer. Dell, Inc.

Author: Daijar Mazum
Country: Yemen
Language: English (Spanish)
Genre: Technology
Published (Last): 13 September 2010
Pages: 380
PDF File Size: 16.35 Mb
ePub File Size: 19.92 Mb
ISBN: 117-6-99660-488-9
Downloads: 29299
Price: Free* [*Free Regsitration Required]
Uploader: Tygorr

A NOTE indicates important information that helps you make better use of your computer. Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. Trademarks used in this text: Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Before working inside your computer, read the safety information that shipped with your computer. For additional safety best practices information, see the Regulatory Compliance Homepage at www.

Before performing these procedures, turn off the computer, disconnect the AC adapter from the electrical outlet and the computer, disconnect the modem from the wall connector and the computer, and remove any other external cables from the computer. To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as a connector on the back of the computer.

Only a certified service technician should perform repairs on your computer. To help prevent damage to the system board, remove the main battery see “Before Working Inside Your Computer” on page 10 before working inside the computer. Removing the Base Cover 1. Ensure that the computer is turned off. Loosen the three captive screws on the base cover and lift the cover off the computer at an angle as shown in the figure. Align the tabs on the base cover to the bottom of the computer.

Tighten the three captive screws on the base cover. Slide the battery into the battery bay until it clicks into place. Unless otherwise noted, each procedure assumes that: Recommended Tools The procedures in this document may require the following tools: To avoid losing data, save and close all open files and exit all open programs before you turn off your computer.

Save and close all open files and exit all open programs. The computer turns off after the operating system shutdown process finishes. Ensure that the computer and any attached devices are turned off.

If your computer and attached devices did not automatically turn off when you shut down your operating system, press and hold the power button for at least 8 to 10 seconds until the computer turns off.

Before Working Inside Your Computer Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.

  APEGO ADULTO FEENEY PDF

Damage due to servicing that is not authorized by Dell is not covered by your warranty. To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface, such as a connector on the back of the computer. Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by its edges. Hold a component such as a processor by its edges, not by its pins.

Dell PP39L | eBay

When disconnecting a cable, pull on the cable’s connector or on its pull-tab, not on the cable itself. For cable connectors with locking tabs, press inward on the locking tabs del release the connector. Ensure that the work surface is flat and clean to prevent the computer cover from being scratched. Turn off your computer see Turning Off Your Computer. To disconnect a network cable, first spevs the cable from your computer, and then unplug it from the network device.

Disconnect any telephone or network cables from the computer. To help prevent damage to the system board, you must remove the battery from the battery bay before you service the computer. To avoid damage to the computer, use only the battery designed for this particular Dell computer. Do not use batteries designed for other Dell computers. Turn the computer over. Slide the battery release latch until it clicks into place. Slide the battery out of the battery bay. Turn the computer top side up, open the display, and press the power button to ground the system board.

Plug the AC adapter into a known, good power source to prevent loss of power. Failure to do so may cause system damage. Ensure that the AC adapter is plugged in and that the main battery is installed properly.

Otherwise, you must enter the system setup program to change the default boot order. Do not interrupt this process once it begins. Doing so may cause damage to the computer.

Follow the instructions that appear on the screen. The computer continues to boot and updates the new BIOS. When the flash update is complete, the computer will automatically reboot. Failure to do so may cause damage to the computer. Ensure that the AC adapter is plugged in, the main battery is properly installed, and a network cable is attached.

Turn on the computer. Locate the latest BIOS update file for your computer at support. Click Download Now to download the file. The File Download window appears. Click Save this program to disk, and then click OK. The Save In window appears. Click the down arrow to view the Save In menu, select Desktop, and then click Save. The file downloads to your desktop. Click Close if the Download Complete window appears.

The file icon appears on your desktop and is titled the same as the downloaded BIOS update file. Doing so may cause system damage. Double-click the file icon on the desktop and follow the instructions on the screen. To help prevent damage to the system board, remove the main battery see Before Working Inside Your Computer before working inside the computer.

  DALLAS DS1307 PDF

Dell Studio 15 ()

Removing the Camera Module 1. Follow the instructions in Before You Begin. Remove the display panel see Removing the Display Panel. Remove the two screws that secure the camera to the display cover. Lift the camera board from the display cover.

Dell Studio 15 (1555) Review

Replace and tighten the two screws securing the camera to the display cover. Replace the display panel see Replacing the Display Panel. Removing the Center Control Cover 1 1. Follow the procedures in Before You Begin. Remove the screw securing the center control cover from the battery bay.

Turn the computer over and open the display as far as possible. Pry out the center control cover with dekl plastic scribe starting from the battery bay location at the back of the computer.

Ease the center control cover up. Align the hooks beneath the center control cover to the slots on the palm rest and snap the cover in place. Close the display and turn over the computer.

In the battery bay, replace the screw that secures the center control cover. Removing the Coin-Cell Battery 1. Remove the base cover see Removing the Base Cover. Use a plastic scribe to pry up the coin-cell battery from the slot.

Hold the coin-cell battery with the positive side up. Slide the coin-cell battery into the slot and gently press until it snaps to the slot. Replace the base cover see Replacing the Base Cover.

Similar Notebooks

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface such as the back panel on the computer. To prevent intermittent contact between the ZIF-socket cam screw and the processor when removing or replacing the processor, press to apply slight pressure to the center of the processor while turning the cam screw. To avoid damage to the processor, hold the eell so that it is perpendicular to the processor when turning the cam screw.

Removing the Processor Module 1.

Remove the processor heat sink see Removing the Processor Heat Sink. To loosen the ZIF socket, use a small, flat-blade screwdriver and rotate the ZIF-socket cam screw counterclockwise until it comes to the cam stop. To ensure maximum cooling for the processor, do not touch the heat transfer areas on the processor thermal-cooling assembly.

The oils in your skin can reduce the heat transfer capability of the thermal pads. When removing the processor module, pull the module straight up.