FIDC tracking water injection system osa User manual v4w Page 2 GETTING TO KNOW THE AQUAMIST HFS-6 osa Aquamist has been. WORKS has been using Aquamist Water Injection since We have seem them all since then and still strongly believe these are the most well thought out. Retired System Information. Below you will find technical info and original sales info for the systems. Aquamist HFS-6 Injection System. Aquamist HFS
|Published (Last):||27 March 2012|
|PDF File Size:||18.75 Mb|
|ePub File Size:||1.96 Mb|
|Price:||Free* [*Free Regsitration Required]|
Jet sizes from 0. It is normally fitted to the vacuum side of the inlet manifold 2D mode for applications where load signal throttle angle sensor or manifold absolute pressure sensor MAP sensor is available. Peak pressure can gfs-6 as high as psi! A pre-pressurized system enables instant response on demand.
Retired System Information
Skip to main content. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab Add to watch list.
Seller assumes all responsibility hfs6- this listing. For additional information, see the Global Shipping Program terms and conditions hrs-6 opens in a new window or tab.
The system provides a pre-pressurized water line up to 8 bars and the flow rate is metered by our latest High speed Valve HSV. In hard water areas, clean the filter in a small glass of diluted household lime-remover occasionally.
The special magnetic stainless armature is set in motion by strong magnetic field induced by a powerful solenoid. Delivery times aauamist vary, especially during peak periods. As usual, except for the water tank, the system is supplied with everything needed to be fitted with ease. Thread size of the jet is M8x0. How does it work? With the best failsafe system in the industry, and a standard 13ohm injector that could be be driven by a spare PWM channel from your EMS, the HFS-5 easily integrates into nearly any application.
Aquamist 2c The 2c is designed for stand-alone EMS systems. Water is then delivered without being in contact with the drive-motor, pressure and delivery rate is regulated by internal high-tech electronic circuitry. Water travelling through these grooves picks up a swirling motion before leaving the small hole on the tip, causing an atomising effect, turning the water into a fine mist: This inline valve is made of high grade stainless steel.
Hfz-6 you will find technical info and original sales info for the systems. Water is being filled and retained between the two valves during the induction stroke armature is pulled against the springwater is then pushed out by the action of compressed spring and the armature when the electric-field is shut-off, high pressure is the product of spring force and the cross-section area of the armature tip.
Developed with years of experience in World Rally Aqua,ist racing and feedback from the industry by the aquamish demanding users, the HFS-6 surpasses all other systems in operation, performance, and reliability. Sep 20, Water travels through hfs-66 grooves, acquiring a swirling motion before leaving the small aquamidt on the tip: Add to watch list.
In addition, it has diagnostic circuitry designed to detect blocked water-jets and cut pipes. The green LED indicates successful detection of fuel injection pulses and the red LED lights up when water is being injected preset manifold pressure is reached.
Delivery time is estimated using our aquamisst method which is based on the buyer’s proximity aquamistt the item location, the shipping service selected, the seller’s shipping history, and other factors. Refinements such as flow rate and block jet detection can easily be obtained with a minimum of signal conditioning parts, to achieve a fully integrated water injection system with diagnostic capablities.
Sell one like this. A special output link from the ECU can inform other systems in the event of a fault condition, so boost-pressure can be lowered to minimize engine damage.
Two colored LEDs are mounted on the top side of the box. The system provides a pre-pressurized water line up to 8 bars and the flow rate is metered by our High Speed Valve HSV. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.
The similarity ends when the manual pump actions is replaced by electro-magnetic fields and speed is also cranked up to about 50 strokes a second! For those who want a 3-D water injection MAP but do not want to spend the time-consuming task of mapping, this system is perfect for you.
For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees. After several signal conditioning stages it finally arrives at the pulse-width-modulator stage, and the output signal is then converted into digital pulses before being sent to the electro-magnetic water valve.
San Diego, California, United States.
A high pressure pump with NO mechanical links, thus eliminated damages caused by jamming. The ERL electro-magnetic pump In order to find a pump that will reliably perform under the harsh environment of the engine bay, we have no alternatives but to design our own.
Aquamkst System Information Below you will find technical info and original sales info for the systems.
Of course a pressure of at least 3 bar is required. Aquamist 1s The 1s is a single stage system that consists of an ERL high-pressure electro-magnetic water pump, adjustable pressure switch, plus all hhfs-6 necessary hardware to form the basis of a starter kit.
See full item description. It is normally fitted to the vacuum side of the inlet manifold 2D mode.